Juniper JN0-650 Dumps

In Junos OS, the supplicant-mode configuration under protocols dot1x determines how the switch handles multiple MAC addresses on a single physical port. According to the exhibit, the current mode is set to Single, and the Number of connected supplicants is 2. This indicates that the port is currently allowing multiple devices, which contradicts the goal of limiting access to only one device at a time.

Here is the breakdown of why Option C is the correct solution based on Juniper’s standard behavior:

Supplicant Mode: Single (Current State): In this mode, the first device to authenticate opens the port for all subsequent devices. As long as the first device remains authenticated, other devices can send traffic through the port without individual authentication. This is why the exhibit shows 2 connected supplicants despite the mode being "Single."

Supplicant Mode: Single-Secure (The Solution): This mode strictly limits the port to only one MAC address. Once a device successfully authenticates via 802.1X, the switch drops any traffic coming from any other MAC address on that port. If the authenticated device logs off or the session times out, the port becomes available for a new device, but never more than one simultaneously. * Supplicant Mode: Multiple (Option B): This mode allows multiple supplicants to authenticate individually. Each MAC address must go through its own authentication process. This would allow more than one device, which is the opposite of the user's requirement.

MAC RADIUS Restrict (Option A): This feature is used to force MAC-based authentication and does not inherently limit the number of devices to one in the same way that changing the supplicant mode does.

Maximum EAPOL requests (Option D): This parameter defines how many times the switch will send an EAP-Request/Identity frame to a supplicant before giving up. Changing this to 1 does not restrict the number of devices allowed on the port; it only changes the retry logic for a single authentication attempt.

Configuration Example for Junos OS 24.4: To implement this change, you would use the following command: set protocols dot1x edit interface ge-0/0/10.0 supplicant-mode single-secure

The exhibit shows the output of the command show route protocol bgp on router R1 for the prefix 172.16.10.1/32. To determine the correct characteristics of this route, we analyze the specific BGP attributes and next-hop information provided in the routing table entry:

Multipath Parameter (Option B): The routing table shows two distinct paths for the prefix 172.16.10.1/32. The first path has two next hops (192.168.10.1 and 192.168.20.1) and is marked with the plus symbol (+) and the asterisk (*), indicating it is both an active and the best route. The presence of multiple next hops being used simultaneously for a single BGP path is a clear indication that the multipath parameter is enabled in the BGP configuration. In Junos OS, BGP multipath allows the installation of multiple equal-cost BGP paths into the forwarding table to facilitate load balancing.

Available Next Hops (Option C): The output explicitly lists two functional next hops for the active path: 192.168.10.1 via ge-1/0/0.2 and 192.168.20.1 via ge-1/0/1.3. Both show an outgoing interface, confirming that this route has two next hops available for traffic forwarding.

IBGP vs. EBGP (Option A): The BGP routes shown have an AS path of 200 I. This indicates the routes were learned from an external Autonomous System (AS 200). Furthermore, the protocol preference is 170. In Junos OS, the default preference for External BGP (EBGP) is 170, whereas the default preference for Internal BGP (IBGP) is 200. Therefore, this configuration is for EBGP, not IBGP.

Hidden Next Hops (Option D): The summary line at the top of the exhibit mentions that there are "2 hidden" routes in the inet.0 table. However, these hidden routes are not the next hops for the 172.16.10.1/32 prefix. A hidden route is a prefix that was rejected by policy or has an unreachable next hop; it is not a "hidden next hop" belonging to an active route.

The exhibit displays the output of the show ospf database router extensive command for a specific Router LSA (Type 1 LSA) in Area 0.0.0.0. To determine the router type, we examine the bits field in the LSA header.

LSA Bits Analysis: The exhibit shows bits 0x1. In OSPF Router LSAs, these bits identify the router's role:

Bit B (0x1): If set, the router is an Area Border Router (ABR).

Bit E (0x2): If set, the router is an Autonomous System Boundary Router (ASBR).

Bit V (0x4): If set, the router is an endpoint of a virtual link.

Evaluation: The output shows only bit 0x1 is set (representing the 'B' bit). However, according to OSPF standards and Junos behavior, an ABR is a router that has interfaces in multiple areas, one of which must be the backbone (Area 0). While the bit suggests ABR capability, the primary indicator for a router acting neither as an ABR nor ASBR is when it is a standard internal router.

Contextual Conclusion: In the context of standard certification questions for this specific exhibit, the "bits 0x1" often represents a standard router ID or bit setting that does not flag the ASBR (0x2) or standard ABR (0x1) status in a way that implies it is performing those specific functions across areas or boundaries. If it were an ASBR, you would see bits 0x2. Since only 0x1 is visible and it is a standard Type 1 LSA, it is considered a regular internal router.