Juniper JN0-649 Dumps

Reviewing POE Interface Information:

The exhibit shows the output of show poe interface and show poe controller commands.

The show poe interface command provides information about the PoE (Power over Ethernet) status on each interface.

Maximum Wattage Allocation:

The show poe controller output indicates that the maximum power available is 100 watts:

plaintext

Copy code

Controller Maximum Power consumption Guard Management Status Lldp

index power band

0 100.00W 22.40W 10W Class AT_MODE Disabled

Thus, statement A is correct.

Power Consumption and Interface Priority:

The interface ge-0/0/11 has a high priority with a max power of 25.4W and current consumption of 11.4W:

plaintext

Copy code

ge-0/0/11 Enabled ON 25.4W(L) High 11.4W 4

Given its high priority, ge-0/0/11 will continue to receive power even if the total power consumption exceeds 90 watts, as high-priority interfaces are less likely to be powered off when resources are low.

POE Status on Interfaces:

The ge-0/0/0 interface is shown as Enabled OFF, indicating PoE is not currently enabled.

plaintext

Copy code

ge-0/0/0 Enabled OFF 15.4W Low 0.0W not-applicable

PoE+ Support:

The ge-0/0/10 interface has a power class of 4, which indicates support for PoE+.

plaintext

Copy code

ge-0/0/10 Enabled ON 25.4W(L) Low 11.0W 4

References:

Exhibit output for show poe interface

Understanding PoE and PoE+ classes and priorities

Multitenancy with Routing Instances:

In a multitenant network, different tenants are isolated using routing instances.

Each routing instance can have its own routing table and policies.

BGP and Load Balancing:

BGP (Border Gateway Protocol) is often used for interconnecting different autonomous systems or for internal routing.

Load balancing in BGP can be achieved using the multipath feature, which allows the installation of multiple paths to the same destination in the routing table.

Additionally, configuring per-packet load balancing ensures that traffic is distributed across multiple paths more granularly.

Configuring Multipath in BGP:

Hierarchy Considerations: The multipath option must be configured at appropriate hierarchies to ensure it applies to the correct scope (either globally or within a specific routing instance).

Detailed Configuration:

Statement C: Configure a load-balance per-packet policy and apply it at the [edit routing-options forwarding-table] hierarchy.

Correct: Configuring a load-balance per-packet policy ensures that packets are distributed evenly across multiple paths. This is crucial for achieving effective load balancing.

Configuration Example:

shell

Copy code

set routing-options forwarding-table export load-balance-per-packet

Policy Definition Example:

shell

Copy code

set policy-options policy-statement load-balance-per-packet term 1 then load-balance per-packet

Statement D: Configure the multipath option at the [edit routing-instances routing-options] hierarchy.

Correct: Configuring multipath within a routing instance ensures that the load balancing feature is applied specifically to that instance, which is crucial in a multitenant environment.

Configuration Example:

shell

Copy code

set routing-instances routing-options multipath

References:

Useful Juniper Commands

Juniper Routing Instances and Multipath Configuration

These configurations ensure that load balancing is achieved within each routing instance, leveraging both per-packet load balancing and the multipath feature in Junos OS for BGP. By configuring at the forwarding-table and routing-instance levels, you ensure the load balancing behavior is correctly applied to achieve the desired network performance and redundancy.

In a PIM-SM (Protocol Independent Multicast - Sparse Mode) network setup:

Before the formation of the rendezvous-point tree, a join message is sent from R1 to R3 (RP):

R1, being the router connected to the receiver, sends a PIM join message towards the RP (R3) to join the multicast group.

Before the formation of the rendezvous-point tree, an IGMP is sent from the Receiver to R1:

The receiver sends an IGMP membership report to its directly connected router (R1), indicating its interest in joining a multicast group.

References:

The behavior of PIM-SM and the process of join messages and IGMP reports are covered in multicast networking sections of network configuration and design guides​​​​.