Juniper JN0-636 Dumps

To enable inter-tenant communication with tenant system, you need to use an external router or a logical tunnel interface. The other options are incorrect because:

• A. Interconnecting EVPN switch is not a valid solution for inter-tenant communication with tenant system. EVPN (Ethernet VPN) is a technology that provides layer 2 connectivity over an IP network. It can be used to connect different logical systems on the same device, but not tenant systems. Tenant systems are isolated from each other and do not share the same layer 2 domain1.
• B. Interconnecting VPLS switch is also not a valid solution for inter-tenant communication with tenant system. VPLS (Virtual Private LAN Service) is another technology that provides layer 2 connectivity over an IP network. It can also be used to connect different logical systems on the same device, but not tenant systems. Tenant systems are isolated from each other and do not share the same layer 2 domain1.

Therefore, the correct answer is C and D. You need to use an external router or a logical tunnel interface to enable inter-tenant communication with tenant system. To do so, you need to perform the following steps:

• For external router, you need to connect the external router to the interfaces of the tenant systems that you want to communicate with. You also need to configure the routing protocols and policies on the external router and the tenant systems to exchange routes and traffic. The external router acts as a gateway between the tenant systems and provides layer 3 connectivity2.
• For logical tunnel interface, you need to create a logical tunnel interface on the device and assign it to a tenant system. You also need to configure the IP address and routing protocols on the logical tunnel interface and the tenant systems that you want to communicate with. The logical tunnel interface acts as a virtual link between the tenant systems and provides layer 3 connectivity3.

References:

• Tenant Systems Overview
• Example: Configuring Inter-Tenant Communication Using External Router
• Example: Configuring Inter-Tenant Communication Using Logical Tunnel Interface

The IPS signature database is one of the major components of the intrusion prevention system (IPS). It contains definitions of different objects, such as attack objects, application signature objects, and service objects, that are used in defining IDP policy rules. As a response to new vulnerabilities, Juniper Networks periodically provides a file containing attack database updates on the Juniper Networks website. You can download this file to protect your network from new threats. Note: IPS does not need a separate license to run as a service on the SRX Series Firewall; however, a license is required for IPS updates1.

When you configure a chassis cluster, the two nodes back up each other, with one node acting as the primary device and the other as the secondary device, ensuring stateful failover of processes and services in the event of system or hardware failure. If the primary device fails, the secondary device takes over processing of traffic2.

To download and install the IPS signature database to a device operating in chassis cluster mode, you must perform the following steps:

• Download the IPS signature package from the Juniper Networks website to the primary node of the chassis cluster. You can use the request security idp security-package download CLI command or the Security Director user interface to download the package. Note: You must have a valid license key installed on the device to download the package3.
• Install the IPS signature package on the primary node of the chassis cluster. You can use the request security idp security-package install CLI command or the Security Director user interface to install the package. Note: You must reboot the primary node after installing the package3.
• Synchronize the IPS signature package from the primary node to the backup node of the chassis cluster. You can use the request security idp security-package install-backup CLI command or the Security Director user interface to synchronize the package. Note: You do not need to reboot the backup node after synchronizing the package3.

Therefore, the correct answer is A. You must download and install the IPS signature package on the primary node. The other options are incorrect because:

• B. The first synchronization of the backup node and the primary node is performed automatically after you install the package on the primary node. You do not need to perform it manually3.
• C. The first time you synchronize the IPS signature package from the primary node to the backup node, the primary node does not need to be rebooted. You only need to reboot the primary node after installing the package3.
• D. The IPS signature package does not need to be downloaded and installed on the primary and backup nodes separately. You only need to download and install it on the primary node and then synchronize it to the backup node3.

References:

• IDP Signature Database Overview
• Understanding IDP Signature Database for Migration
• Configuring Chassis Clustering on SRX Series Devices