Refer to the exhibit.
A new Cisco Nexus 5548 Switch connects to a network. SAN switching is configured on the switch. The switch fc2/10 NP uplink is shown in the exhibit. Which action ensures that fc2/10 is in an up state?
The VXL AN fabric is deployed with this configuration:
●The VL AN 50 interface has no IP address on VTEP1 and VTEP4.
●The VLAN 100 interface has no IP address on VTEP2 and VTEP3.
● nve1 interface is configured on all VTEPs.
Host A experiences timeouts when attempting to ping host B. Which set of actions allows host A to reach host B7
"A network engineer troubleshoots an issue at a Cisco data center environment with these conditions:
• The data center has Cisco Nexus 9000 Series Switches running the vPC setup.
• The gateway of the servers is an HSRP IP address between the VLAN interfaces configured on both Cisco Nexus switches.
• Some of the client application servers are implementing fast-path forwarding for the return traffic.
• Those servers are sending the return traffic to the VLAN interface MAC address instead of the HSRP MAC address.
The network engineer discovers that some traffic is dropped because it passes the vPC peer link to be forwarded out the vPC interface. What must be configured on the vPC switches to resolve the issue?
Refer to the exhibit. A network engineer is configuring the FCoE N_Port virtualization storage area network. After the initial implementation, server 11 fails to connect to the disk array. Which action resolves the issue?
Refer to the exhibit.
An engineer is configuring boot from iSCSI on a Cisco UCS B-Series Blade Server, but the LUN fails to mount. Which action resolves the issue?
Refer to the exhibit.
An OSPF adjacency between Router-A and Router-B cannot reach the FULL state. Which action resolves the issue?
Refer to the exhibit.
The HSRP instance on both switches is showing as active. Which action resolves the issue?
An engineer attempts to register Cisco UCS Manager to Cisco UCS Central, but the registration fails. The engineer can ping Cisco UCS Central from UCS Manager. Which two actions must the engineer attempt to resolve the problem? (Choose two.)
Refer to the exhibit.
The scheduler job fails to run. Which action resolves the issue?
An engineer upgrades Cisco UCS firmware from release 3. 1(2) to release 3. 1(3) using Autolnstall. Both fabric interconnects go ofline during the software upgrade installation and issue multiple F SM retries in the DeployPollActivate stage. Which set of actions resolves the issue?
Refer to the exhibit.
The initiator that has FC ID 0x970102 fails to communicate with the target that has FC ID 0x970200. What action resolves the issue?
Refer to the exhibit.
HSRP adjacency fails to form between Nexus7K-1 and Nexus7K-2. Which action should be taken to solve the problem?
An engineer is troubleshooting a custom AV pair that was created by a client on an external authentication server to map a read-only role for a specific security domain. Which AV pair solves the problem?
An engineer troubleshoots a VXLAN EVPN data center. The applications in the data center fail to reach the DNS server that is located at IP 10.10.10.10. The engineer examines the BGP EVPN routing table and notes that the IP prefix route covers the DNS server is missing. Which action resolve the issue?
Your client reports that many flaps and server cluster disconnects occur in their data center. While troubleshooting the issue, you discover a network attack hitting their Cisco Nexus 7000 Series Switches and determine that the source IP addresses are spoofed. Which first-line security solution resolves this issue?
Refer to the exhibit.
A customer network uses OSPFv2 and MP-BGP protocols A network administrator installs a new Cisco Nexus Switch in the data center but experiences a BGP RIB failure Which action solves the issue?
Refer to the exhibit.
The EEM script is applied in the default VDC to collect the outputs during high CPU utilization on the Cisco Nexus 7000 Series Switch for all VDCs. Which configuration set must be added to the script to fix the issue?
Refer to the exhibit.
A blade that is connected to FI-B fails to boot from a SAN LUN. The boot policy is configured to boot by using vHBA1 as the SAN Primary. Which set of actions resolves the issue?
Refer to the exhibit.
An engineer must strictly enforce the port security configuration database in the Fibre Channel fabric. A new device has been connected to the Fibre Channel storage interface that was configured for port security. The port security was enabled for the VSAN that the port belongs to. Despite the configuration, the rogue devices can log into the fabric. Which action resolves the issue?
Refer to the exhibit.
An engineer performs a POST operation using REST API on the Cisco Nexus switch to retrieve a managed object, but the operation fails. Which configuration resolves the issue?
A system administrator connects a Cisco Nexus 2248PQ FEX to a fabric interconnect to expand the ports that
are available for connecting Cisco UCS C-Series Rack Servers. In Cisco UCS Manager, the administrator does
not see the servers connected to this FEX. Which action should be taken to resolve the issue?