dumpspedia logo
Refer to the exhibit.
The network administrator configured VRF lite for customer A. The technician at the remote site misconfigured VRF on the router. Which configuration will resolve connectivity for both sites of customer_a?
Refer to the exhibit.
Which control plane policy limits BGP traffic that is destined to the CPU to 1 Mbps and
ignores BGP traffic that is sent at higher rate?
Refer to the exhibit.
An OSPF neighbor relationship between R2 and R3 is showing stuck in EXCHANGE/EXSTART state. The neighbor is established between R1 and R2. The network engineer can ping from R2 to R3 and vice versa, but the
neighbor is still down. Which action resolves the issue?
Refer to the exhibit.
An engineer configures two ASBRs 10 4 17.6 and 10 4 15 5 in an OSPF network to redistribute routes from EIGRP However, both ASBRs show the EIGRP routes as equal costs even though the next-hop router 10 4 17 6 is closer to R1 How should the network traffic to the EIGRP prefixes be sent via 10 4.17.6?
Refer to the exhibit A network engineer notices that the configured track option is down Which configuration resolves the issue*?
A network administrator is troubleshooting a high utilization issue on the route processor of a router that was reported by NMS The administrator logged into the router to check the control plane policing and observed that the BGP process is dropping a high number of routing packets and causing thousands of routes to recalculate frequently. Which solution resolves this issue?
Refer to the exhibit.
An engineer is trying to connect to R1 via Telnet with no success. Which configuration resolves the issue?
Refer to the exhibit.
An engineer recently implemented uRPF by configuring the ip verify unicast source reachable-via rx command on interface gi0/3 The engineer noticed right after implementing F that an inbound packet on the giO-3 interface with a source address of 172 16 3 251 was dropped. Which action resolves the issue?
A network administrator opens a telnet connection to the router and gets the message:
R1#telnet 10.1.1.2
Trying 10 1.1 2 Open
(Connection to 10.1.1.2 closed by foreign host)
Router R2 is configured with enable secret and password commands. Which action resolves the issue?
Refer to the exhibit R2 can reach Loopback222, but R1 SW1 and PC1 cannot communicate with 172.16.222 254 R1 and R2 configurations are shown here
Which EIGRP configuration command resolves the issue?
An engineer notices that R1 does not hold enough log messages to Identity the root cause during troubleshooting Which command resolves this issue?
Which SNMP verification command shows the encryption and authentication protocols that are used in
SNMPV3?
Which attribute eliminates LFAs that belong to protected paths in situations where links in a network are connected through a common fiber?
Which command is used to check IP SLA when an interface is suspected to receive lots of traffic with options?
Refer to the exhibit.
A junior engineer updated a branch router configuration. Immediately after the change, the engineer receives calls from the help desk that branch personnel cannot reach any network destinations. Which configuration restores service and continues to block 10.1.1.100/32?
Drag and drop the operations from the left onto the locations where the operations are performed on the right.
Refer to the exhibit.
An engineer is troubleshooting BGP on a device but discovers that the clock on the device does not correspond to the time stamp of the log entries. Which action ensures consistency between the two times?
Refer to the exhibit.
The none area 0 routers in OSPF still receive more specific routes of 10.1.1.0.10.1.2.0.10.1.3.0 from area 0. Which action resolves the issue?
Refer to the exhibit An engineer is troubleshooting an OSPF adjacency issue between directly connected routers R1 and R2 Which configuration resolves the issue?
A)
B)
C)
D)
Refer to the exhibit.
A network administrator successfully logs in to a switch using SSH from a (RADIUS server When the network administrator uses a console port to access the switch the RADIUS server returns shell:priv-lvl=15’’ and the switch asks to enter the enable command \ the command is entered, it gets rejected. Which command set is used to troubleshoot and reserve this issue?
An engineer configured a router with this configuration
ip access-hst DENY TELNET
10 deny tcp any any eq 23 log-input
The router console starts receiving log message :%SEC-6-IPACCESSLOGP: list DENY_TELNET denied tcp 192.168.1.10(1022)(FastEthernet1/0 D508.89gb.003f) ->192.168.2.20(23), 1 packet"
Which action stops messages on the console while still denying Telnet?
Drag and Drop the IPv6 First-Hop Security features from the left onto the definitions on the right.
Drag and drop the MPLS VPN concepts from the left onto the correct descriptions on the right.
Which protocol is used to determine the NBMA address on the other end of a tunnel when mGRE is used?
Refer to the exhibit.
Which routes from OSPF process 5 are redistributed into EIGRP?
Refer to the exhibit.
An IT staff member comes into the office during normal office hours and cannot access devices through SSH Which action should be taken to resolve this issue?
An engineer creates a default static route on a router with a hop of 10.1.1.1. On inspection, the engineer finds the router has two VRFs, Red and Blue. The next hop is valid for both VRFs and exists in each assigned VRF. Which configuration achieves connectivity?
A)
B)
C)
D)
R2 has a locally originated prefix 192.168.130.0/24 and has these configurations:
What is the result when the route-map OUT command is applied toward an eBGP neighbor R1 (1.1.1.1) by using the neighbor 1.1.1.1 route-map OUT out command?
Refer to the exhibit.
The output of the trace route from R5 shows a loop in the network. Which configuration
prevents this loop?
A)
B)
C)
D)
Which method changes the forwarding decision that a router makes without first changing the routing table or influencing the IP data plane?
Which two methods use IPsec to provide secure connectivity from the branch office to the headquarters office? (Choose two.)
Drag and drop the ICMPv6 neighbor discovery messages from the left onto the correct packet types on the right.
Refer to the exhibit.
ISP 1 and ISP 2 directly connect to the Internet. A customer is tracking both ISP links to
achieve redundancy and cannot see the Cisco IOS IP SLA tracking output on the router console. Which command is missing from the IP SLA configuration?
Refer to the exhibit.
The network engineer configured the summarization of the RIP routes into the OSPF domain on R5 but
still sees four different 172.16.0.0/24 networks on R4. Which action resolves the issue?
Refer to the exhibit.
A company is evaluating multiple network management system tools. Trending graphs generated by SNMP data are returned by the NMS and appear to have multiple gaps. While troubleshooting the issue, an engineer noticed the relevant output. What solves the gaps in the graphs?
Which two statements about redistributing EIGRP into OSPF are true? (Choose two)
Refer to the exhibit.
Drag and drop the credentials from the left onto the remote login information on the right to resolve a failed login attempt to vtys. Not all credentials are uf SLA by defining frequency and schedulingsed
Refer to the exhibit.
While troubleshooting an EIGRP neighbor adjacency problem, the network engineer notices that the interface connected to the neighboring router is not participating in the EIGRP process. Which action resolves the issues?
Refer to the exhibit.
An engineer is trying to configure local authentication on the console line, but the device is trying to authenticate using TACACS+. Which action produces the desired configuration?
Which protocol is used in a DMVPN network to map physical IP addresses to logical IP addresses?
Drag and drop the DHCP messages from the left onto the correct uses on the right.
Refer to the exhibit.
An engineer configures a static route on a router, but when the engineer checks the route
to the destination, a different next hop is chosen. What is the reason for this?
Drag and drop the MPLS concepts from the left onto the descriptions on the right.
Refer to the exhibit. R1 and R2 cannot establish an EIGRP adjacency. Which action establishes EIGRP adjacency?
Refer to the exhibit.
The administrator can see the traps for the failed login attempts, but cannot see the traps of successful login attempts. What command is needed to resolve the issue?
Refer to the exhibit An engineer must ensure that R3 sees only type 1 and 2 LSAs in area 1. Which command must the engineer apply on R2?
Drag and drop the descriptions from the left onto the IPv6 first hop security features on the right. Not all options are used.
The network administrator configured R1 for Control Plane Policing so that the inbound Telnet traffic is policed to 100 kbps. This policy must not apply to traffic coming in from 10.1.1.1/32 and 172.16.1.1/32. The administrator has configured this:
The network administrator is not getting the desired results. Which set of configurations resolves this issue?
Refer to the exhibit. R2 has two paths to reach 192.168.13.0/24. but traffic is sent only through R3. Which action allows traffic to use both paths?
Refer to the exhibit.
An engineer identifier a Layer 2 loop using DNAC. Which command fixes the problem in the SF-D9300-1 switch?
An engineer configured SNMP notifications sent to the management server using authentication and encrypting data with DES. An error in the response PDU is received as "UNKNOWNUSERNAME. WRONGDIGEST". Which action resolves the issue?
Refer to the exhibit.
A company with autonomous system number AS65401 has obtained IP address block 209.165.200.224/27 fro, ARIN. The company needed more IP addresses and was assigned block209.165.202.128/27 from ISP2. An engineer is ISP1 reports they are receiving ISP2 routes from AS65401. Which configuration onR1 resolves the issue?
A)
B)
C)
D)
Refer to the exhibit.
A user cannot SSH to the router. What action must be taken to resolve this issue?
An engineer sets up a DMVPN connection to connect branch 1 and branch 2 to HQ branch 1 and branch 2 cannot communicate with each other. Which change must be made to resolve this issue?
Refer to the exhibits.
When DMVPN is configured, which configuration allows spoke-to-spoke communication using loopback as a tunnel source?
Refer to Exhibit.
A network administrator added one router in the Cisco DNA Center and checked its discovery and health from the Network Health Dashboard. The network administrator observed that the router is still showing up as unmonitored. What must be configured on the router to mount it in the Cisco DNA Center?
Refer to the exhibit.
The neighbor relationship is not coming up Which two configurations bring the adjacency up? (Choose two)
Refer to the exhibit. The remote server is failing to receive the NetFlow data Which action resolves the issue?
Refer to the exhibit.
An engineer configured BGP between routers R1 and R3 The BOP peers cannot establish neighbor adjacency to be able to exchange routes. Which configuration resolves this issue?
Refer to the exhibit.
A network administrator is troubleshooting OSPF adjacency issue by going through the console logs in the router, but due to an overwhelming log message stream it is impossible to capture the problem Which two commands reduce console log messages to relevant OSPF neighbor problem details so that the issue can be resolved? (Choose two)
Refer to the exhibit. Which configuration command establishes an EIGRP neighbor adjacency between the hub and spoke?
A network administrator must optimize the segment size of the TCP packet on the DMVPN IPsec protected tunnel interface, which carries application traffic from the head office to a designated branch. The TCP segment size must not overwhelm the MTU of the outbound link. Which configuration must be applied to the router to improve the application performance?
A network is configured with IP connectivity, and the routing protocol between devices started having problems right after the maintenance window to implement network changes. Troubleshoot and resolve to a fully functional network to ensure that:
R4
R5
Refer to the exhibit.
R1 is configured with IP SLA to check the availability of the server behind R6 but it kept failing. Which configuration resolves the issue?
Refer to the exhibit.
The R1 OSPF neighbor is not receiving type 5 external LSAs for 132.108.2.0/24 and 132.108.3.0/24 networks. Which configuration command resolves the issue?
Refer to the exhibit.
An engineer configures SW101 to send OSPFv3 interfaces state change messages to the server. However, only some OSPFv3 errors are being recorded. which organization resolves the ..?
A network administrator added a new spoke site with dynamic IP on the DMVPN network. Which configuration command passes traffic on the DMVPN tunnel from the spoke router?
Which routing protocol is used by the PE router to advertise routes to a CE router without redistribution or static after removing the RD tag from the P router?
Refer to the exhibit. The network administrator configured the branch router for IPv6 on the E 0/0 interface The neighboring router is fully configured to meet requirements, but the neighbor relationship is not coming up. Which action fixes the problem on the branch router to bring the IPv6 neighbors up?
Refer to the exhibit. Which action restores the routes from neighbors while still filtering 1.1.1.0/24?
An engineer needs dynamic routing between two routers and is unable to establish OSPF adjacency. The output of the show ip ospf neighbor command shows that the neighbor state is EXSTART/EXCHANGE. Which action should be taken to resolve this issue?
Refer to the exhibit.
SanFrancisco and Boston routers are choosing slower links to reach each other despite the direct links being up Which configuration fixes the issue?
An engineer configured a DHCP server for Cisco IP phones to download its configuration from a TFTP server, but the IP phones failed to toad the configuration What must be configured to resolve the issue?
When configuring Control Plane Policing on a router to protect it from malicious traffic, an engineer observes that the configured routing protocols start flapping on
that device. Which action in the Control Plane Policy prevents this problem in a production environment while achieving the security objective?
Which feature drops packets if the source address is not found in the snooping table?
An engineer must configure a Cisco router to initiate secure connections from the router to other devices in the network but kept failing. Which two actions resolve the issue? (Choose two.)
Exhibit:
An engineer configured R2 and R5 as route reflectors and noticed that not all routes are sent to R1 to advertise to the eBGP peers. Which iBGP routers must be configured as route reflectors to advertise all routes to restore reachability across all networks?
Refer to the exhibit.
A network administrator is using the DNA Assurance Dashboard panel to troubleshoot an OSPF adjacency that failed between Edge_NYC interface GigabitEthernet1/3 with Neighbor Edge_SNJ. The administrator observes that the neighborship is stuck in exstart state. How does the administrator fix this issue?
Refer to Exhibit.
Which two configurations allow clients to get dynamic ip addresses assigned?
After some changes in the routing policy, it is noticed that the router in AS 45123 is being used as a transit AS router for several service provides. Which configuration ensures that the branch router in AS 45123 advertises only the local networks to all SP neighbors?
A)
B)
C)
D)
Refer to the exhibit.
An engineer wanted to set a tag of 30 to route 10 1.80.65/32 but it failed How is the issue fixed?
Refer to the exhibit.
An engineer is troubleshooting a failed Telnet session from PC to the DHCP server. Which action resolves the issue?
Refer to the exhibit.
An engineer configured IP SLA on R1 to avoid the ISP link flapping problem. but it is not working as designed IP SLA should wait 30 seconds before switching traffic to a secondary connection and then revert to the primary link after waning 20 seconds, when the primary link is available and stabilized. Which configuration resolves the issue?
Refer to the exhibit A network engineer is troubleshooting an AAA authentication issue for R1 from R2 When an engineer tries to open a telnet connection to R1 it opens the connection but shows a %Authorization failed error message on the terminal and closes the connection silently Which action resolves the issue?
Refer to the exhibit. A network administrator configured an IPv6 access list to allow TCP return traffic only, but it is not working as expected. Which changes resolve this issue?
Refer to the exhibit.
The OSPF routing protocol is redistributed into the BGP routing protocol, but not all the OSPF routes are distributed into BGP Which action resolves the issue?
Drag and drop the LDP features from the left onto the descriptions on the right
Refer to the exhibit.
A network administrator logs into the router using TACACS+ username and password credentials, but the administrator cannot run any privileged commands Which action resolves the issue?
Refer to the exhibit.
A network is under a cyberattack. A network engineer connected to R1 by SSH and enabled the terminal monitor via SSH session to find the source and destination of the attack. The session was flooded with messages, which made it impossible for the engineer to troubleshoot the issue. Which command resolves this issue on R1?
Refer to Exhibit.
The network administrator configured the branch router for IPv6 on the E0/0 interface. The neighboring router is fully configured to meet requirements, but the neighbor relationship is not coming up. Which action fixes the problem on the branch router to bring the IPv6 neighbors up?
Refer to the exhibit.
The network administrator can see the DHCP discovery packet in R1. but R2 is not replying to the DHCP request. The R1 related interface is configured with the DHCP helper address. If the PC is directly connected to the FaO/1 interface on R2, the DHCP server assigns as IP address from the DHCP pool to the PC. Which two commands resolve this issue? (Choose two.)
Refer to the exhibit.
R1 is being monitored using SNMP and monitoring devices are getting only partial information. What action should be taken to resolve this issue?
An engineer configured a Cisco router to send reliable and encrypted notifications for any events to the management server. It was noticed that the notification messages are reliable but not encrypted. Which action resolves the issue?
Refer to the exhibit.
R2 is a route reflector, and R1 and R3 are route reflector clients. The route reflector learns the route to 172.16.25.0/24 from R1, but it does not advertise to R3. What is the reason the route is not advertised?
Refer to the exhibit. The network administrator has configured the Customer Edge router (AS 64511) to send only summarized routes toward ISP-1 (AS 100) and ISP-2 (AS 200).
router bgp 64511
network 172.16.20.0 mask 255.255.255.0
network 172.16.21.0 mask 255.255.255.0
network 172.16.22.0 mask 255.255.255.0
network 172.16.23.0 mask 255.255.255.0
aggregate-address 172.16.20.0 255.255.252.0
After this configuration. ISP-1 and ISP-2 continue to receive the specific routes and the summary route. Which configuration resolves the issue?
Refer to Exhibit.
PC2 is directly connected to R1. A user at PC2 cannot Telnet to 2001:db8:a:b::10. The user can ping
2001:db8:a:b::10 and receive DHCP-related information from the DHCP server. Which action resolves
the issue?
The network administrator configured the router for Control Plane Policrg so that inbound SSH traffic is policed to 500 kbps This policy must apply to traffic coming in from 101010 0<24 and 192 168 10.0/24 networks
The Control Rane Policing is not applied to SSH traffic and SSH is open to use any bandwidth available. Which configuration resolves this issue?
A)
B)
C)
D)
Refer to the exhibit. An engineer configured summarization for the R1 loopback addresses and failed. Which action permits the successful advertisement of the R1 loopback addresses?
Refer to the exhibits.
London must reach Rome using a faster path via EIGRP if all the links are up but it failed to take this path Which action resolves the issue?
Which protocol must be secured with MD-5 authentication across the MPLS cloud to prevent hackers from introducing bogus routers?
Refer to the exhibit.
TCP traffic should be reaching host 10.10.10.10/24 via R2. Which action resolves the issue?
Refer to the exhibit. A network engineer is provisioning end-to-end traffic service for two different enterprise networks with these requirements
The OSPF process must differ between customers on HQ and Branch office routers, and adjacencies should come up instantly.
The enterprise networks are connected with overlapping networks between HO and a branch office
Which configuration meets the requirements for a customer site?
A
A)
B)
C)
D)
Refer to the exhibit. Which configuration advertises more specific routes to R1 without sending a BGP summary route?
An administrator attempts to download the pack NBAR2 file using TFTP from the CPE router to another device over the Gi0/0 interface. The CPE is configured as below:
The transfer fails. Which action resolves the issue?
Refer to the exhibit. Which configuration resolves the IP SLA issue from R1 to the server?
Which control plane process allows the MPLS forwarding state to recover when a secondary RP takes over from a failed primary RP?
Refer lo lhe exhibit. The Customer Edge rouler wants to use AS 100 as the preferred ISP for all external routes and ISP-2 as a backup.
After this configuration, all the backup routes have disappeared from the BGP table on the Customer Edge router. Which set of configurations resolves the issue on the Customer Edge router?
A)
B)
C)
D)
Refer to the exhibit.
Router R2 should be learning the route for 10.123.187.0/24 via EIGRP. Which action resolves the issue without introducing more issues?
:589
Aswitchhas been configured to provide DHCP relay on VLAN 100 to a server with an IP address of 10.1.1.1. The DHCP server is sending syslog reports of multiple TFTP requests that also originate from the switch. As a result, the server CPU exceeded a configured threshold. Which action does the network administrator recommend to bring the server CPU threshold down?
i.
Which two labet distribution methods are used by routers in MPLS? (Choose two )
Refer to the exhibit. An engineer troubleshoots a connectivity problem that is impacting the communication from the users at segment 172.16.3.16/28 to the server farm at 192.168.5.16/ 28. Which configuration resolves the issue on router R1?
Refer to the exhibit.
A network engineer finds that PC1 is accessing the hotel website to do the booking but fails to make payment. Which action resolves the issue?
Which two protocols are used by a P router to transfer VPN traffic between PE routers in an MPLS network? (Choose two.)
Which table is used to map the packets in an MPLS LSP that exit from the same interface, via the same next hop, and have the same queuing policies?
Refer to the exhibit.
After a new regional office is set up,not all guests can access the internet via guest Wi
Fi. Clients are getting the correct IP address from guest Wi-Fi VLAN 364. which action resolves the issue ?
Refer to the exhibit. An engineer must configure a per VRF for TACACS+ for company A. Which configuration on RTG-1 accomplishes the task?
Refer to the exhibit.
A network administrator sets up an OSPF routing protocol for a DMVPN network on the hub router. Which configuration required to establish a DMVPN tunnel with multiple spokes?
An engineer is troubleshooting on the console session of a router and turns on multiple debug commands. The console screen is filled with scrolling debug messages that none of the commands can be verified if entered correctly or display any output. Which action allows the engineer to see entered console commands while still continuing the analysis of the debug messages?
Refer to the exhibit.
Which action makes 10.1.3.2 the feasible successor to reach 10. 200. 1 0/24 for location S42T447E33F95?
Refer to the exhibit.
An engineer must configure DMVPN Phase 3 hub-and-spoke topology to enable a spoke-to-spoke tunnel. Which NHRP configuration meets the requirement on R6?
Refer to the exhibit.
Which interface configuration must be configured on the HUB router to enable MVPN with mGRE mode?
Refer to the exhibit.
When monitoring an IPv6 access list, an engineer notices that the ACL does not have any hits and is causing unnecessary traffic to pass through the interface Which command must be configured to resolve the issue?
Refer to the exhibit.
To provide reachability to network 10.1.1.0 /24 from R5, the network administrator redistributes EIGRP into OSPF on R3 but notices that R4 is now taking a ........... path through R5 to reach 10.1.1.0/24 network. Which action fixes the issue while keeping the reachability from R5 to 10.1.1.0/24 network?
Refer to the exhibit.
All the serial between R1, R2, and R3 have the Same bandwidth. User on the 192.168.1.0/24 network report slow response times while they access resource on network 192.168.3.0/24. When a traceroute is run on the path. It shows that the packet is getting forwarded via R2 to R3 although the link between R1 and R3 is still up. What must the network administrator to fix the slowness?
Refer to the exhibit. An engineer has successfully set up a floating static route from the BRANCH router to the HQ network using HQ_R1 as the primary default gateway When the g0/0 goes down on HQ_R1, the branch network cannot reach the HQ network 192.168.20.0/24. Which set of configurations resolves the issue?
Drag and drop the MPLS VPN device types from the left onto the definitions on the right.
Refer to the exhibit.
R1 is connected with R2 via GigabitEthernet0/0, and R2 cannot ping R1. What action will fix the issue?
Refer to the exhibit.
BGP and EIGRP are mutually redistributed on R3, and EIGRP and OSPF are mutually redistributed on R1. Users report packet loss and interruption of service to applications hosted onthe 10.1.1.0724 prefix. An engineer tested the link from R3 to R4 with no packet loss present but has noticed frequent routing changes on R3 when running the debug ip route command. Which action stabilizes the service?
Refer to the exhibit. The administrator configured route advertisement to a remote low resources router to use only the default route to reach any network but failed. Which action resolves this issue?
Refer to the exhibit. The Los Angeles and New York routers are receiving routes from Chicago but not from each other. Which configuration fixes the issue?
Which Ipv6 first-hop security feature helps to minimize denial of service attacks?
Which two protocols work in the control plane of P routers across the MPLS cloud? (choose two)
Refer to Exhibit.
Traffic from the branch network should route through HQ R1 unless the path is unavailable. An engineer tests this functionality by shutting down interface on the BRANCH router toward HQ_R1 router but 192.168.20.0/24 is no longer reachable from the branch router. Which set of configurations resolves the issue?
A newly Installeo router starts establishing an LDP session from another MPLS router to which it is not directly connected. Which LDP message type responds by target router to the Initiating router using UDP protocol?
Refer to the exhibit.
While troubleshooting a BGP route reflector configuration, an engineer notices that reflected routes are missing from neighboring routers. Which two BGP configurations are needed to resolve the issue? (Choose two)
Refer to the exhibit. An engineer is trying to log in to R1 via R3 loopback address. Which action resolves the issue?
A network engineer is investigating a flapping (up/down) interface issue on a core switch that is synchronized to an NTP server. Log output currently does not show the time of the flap. Which command allows the logging on the switch to show the time of the flap according to the clock on the device?
Refer to the exhibit.
An engineer is trying to generate a summary route in OSPF for network 10.0.0.0/8, but the
summary route does not show up in the routing table. Why is the summary route missing?
Refer to the exhibit.
After applying IPsec, the engineer observed that the DMVPN tunnel went down, and both
spoke-to-spoke and hub were not establishing. Which two actions resolve the issue? (Choose two.)
A network engineer needs to verify IP SLA operations on an interface that shows on indication of
excessive traffic.
Which command should the engineer use to complete this action?
Which Cisco VPN technology can use multipoint tunnel, resulting in a single GRE tunnel interface on the hub, to support multiple connections from multiple spoke devices?
Refer to the exhibit.
A network engineer for AS64512 must remove the inbound and outbound traffic from link A during maintenance without closing the BGP session so that there ............ a backup link over link A toward the ASN. Which BGP configuration on R1 accomplishes this goal?
A)
B)
C)
D)
Refer to the exhibit.
An engineer is trying to connect to a device with SSH but cannot connect. The engineer connects by using the console and finds the displayed output when troubleshooting. Which command must be used in configuration mode to enable SSH on the device?
While working with software images, an engineer observes that Cisco DNA Center cannot upload its software image directly from the device. Why is the image not uploading?
Refer to the exhibit.
Redistribution is enabled between the routing protocols, and nowPC2 PC3, and PC4 cannot reach PC1. What are the two solutions to fix the problem? (Choose two.)
Refer to the exhibit.
An administrator that is connected to the console does not see debug messages when
remote users log in. Which action ensures that debug messages are displayed for remote logins?
Drag and drop the addresses from the left onto the correct IPv6 filter purposes on the right.
Refer to the following output:
Router#show ip nhrp detail
10.1.1.2/8 via 10.2.1.2, Tunnel1 created 00:00:12, expire 01:59:47
TypE. dynamic, Flags: authoritative unique nat registered used
NBMA address: 10.12.1.2
What does the authoritative flag mean in regards to the NHRP information?
Which configuration enabled the VRF that is labeled “Inet” on FastEthernet0/0?
Refer to the exhibit.
AAA server 10.1.1.1 is configured with the default authentication and accounting settings, but the switch cannot communicate with the server Which action resolves this issue?
Refer to the exhibit.
Users in the branch network of 2001:db8:0:4::/64 report that they cannot access the Internet. Which command is issued in IPv6 router EIGRP 100 configuration mode to solve this issue?
What is the role of a route distinguisher via a VRF-Lite setup implementation?
Refer to Exhibit.
Which statement about redistribution from BGP into OSPF process 10 is true?
Refer to the exhibit.
The server for the finance department is not reachable consistently on the 200.30.40.0/24 network and after every second month it gets a new IP address. Which two actions must be taken to resolve this Issue? (Choose two.)
Drag and drop the SNMP attributes in Cisco IOS devices from the left onto the correct SNMPv2c or SNMPV3 categories on the right.
TESTED 04 Jul 2025
Graphical user interface, chart Description automatically generated
Table Description automatically generated with medium confidence
Graphical user interface, text, application Description automatically generated
Diagram Description automatically generated
Graphical user interface, application Description automatically generated
Graphical user interface, application Description automatically generated